Volume 18, Issue No.2


Biomass, bio fuels, biogas, waste, utilization.


In the paper, the authors present actual situation in preparation of bio fuels from biomass in conditions of Slovakia and also some examples of utilization of produced bio fuel. There is short description of bio fuel produced from agricultural waste, from wood and from sewage treatment plant. These 3 ways are most common in our conditions


Acta Mechanica Slovaca. Volume 18, Issue 2, Pages 64–69, ISSN 1335-2393


  Preparation and Utilization of Biogas Produced ...


[1] MacKay, D.: Sustainable energy – without the hot air. UIT Cambridge Ltd., 2009, p.368.
[2] Horbaj, P,; Víglaský, J.; Andrejčák, I.: Využitie bioplynu. ES TU Zvolen, 2008. s. 157, ISBN 978-80-228-1857-5.
[3] Rybár, P.; Rybár, R.; Tauš, P.: Alternatívne zdroje energie. TU FBERG Košice, 2001, s.121.
[4] Vranayová, Z.; Vranay, F.; Očipová, D.: Renewable energy for smart buildings in conditions of the Slovak republic, In: Journal of international scientific publication. Vol. 3, no.1, 2009, p. 486-493. ISSN 1313–2539.
[5] Oravec, M.; Števo, S.; Sekaj, I.: Comparison of using simple genetic algorithm and parallel genetic algorithm in heat transfer model optimization. J. Cyber. Inform., 9, 2010, p. 13–18.
[6] Jandačka, J.; Malcho, M.; Mikulík, M.: Biomasa ako zdroj energie. ES TU v Žiline, 2006, s.240.
[7] Košičanová, D.; Kapalo, P.: A consumer model for researching the integrative effectiveness of renewable energy sources - a design concept of technical equipment. In: Czasopismo
Techniczne. Vol. 109, no. 3, 2012, s. 247-253. ISSN 0011-4561

[8] Tkáč, M.; Hvizdoš, S.: Distributed generation and renewable energy sources for sustainable life. In: Distributed Power Generation Systems. Plzeň, 2005, p. 47-52. ISBN 807043371X.
[9] Trebuňa, P.; Kliment, J.; Halčínová, M.; Fiľo, J; Markovič.: Comparison of agglomerative clustering procedures. 978-80-87539-54-5 Plzeň, SmartMotion, 2013, p. 185–189.
[10] Trebuňa, F.; Šimčák, F.; Bocko, J.; Trebuňa, P.: Failure analysis of mechanical elements in steelworks equipment by methods of experimental mechanics. Eng. Fail. Anal., 17 (4), 2010,
p. 787–801.
[11] Badida, M.; Lumnitzer, E.; Biľová, E.; Fiľo, M.: The uncertainties of environments parameters measurements as tools of the measurements quality improvement. Univerzitet u Kragujevcu, Kragujevac, 2008, p. 1–5.
[12] Puškár, M.; Bigoš, P.; Puškárová, P.: Accurate measurements of output characteristics and detonations of motorbike high-speed racing engine and their optimization at actual atmospheric conditions and combusted mixture composition. Measurement, 45 (5), 2012, p. 1067–1076.
[13] Lázár, M.; Brestovič,T; Schvarzbacherová, E.: Designing low gas flow meters based on the calometric principle of flow rate measuring. In: The Holistic Approach to Environment.
Vol. 1, no. 4, 2011, p. 153-162. ISSN 1848-0071.
[14] Marasová, D. et.al.: Analysis model for determination of contact loads between tube-shaped conveyor belt of a pipe conveyor and carrier rolls. In: Cuprum : Czasopismo naukowo-techniczne górnictwa rud. no. 3, 2010, p. 71-76. ISSN 0137-2815.
[15] Martinka, J.; Kačíková, D.; Hroncová, E.; Ladomerský, J.:Experimental determination of the effect of temperature and oxygen concentration on the production of birch wood main fire emmisions. Journal of Thermal Analysis and Calorimetry. Vol. 110, No.1, p. 485-487, 2012. ISSN 1388-6150.


Latest Issue

ams 2 2016